Advanced Technocracy Inc.
Grain Market, Ambala, Haryana
Send E-mail
Send SMS
Home»Our Products»

Stereo Microscope

Our product range includes a wide range of coiled tube isothermal plug flow reactor, microscope cameras, rtd studies in cstr, annular uv photo reactor, condensation polymerization reactor and combined flow reactor.

REQUEST CALLBACK
Ask Latest Price

Technical Description: 

 In an ideal Plug Flow Reactor (PFTR) there is no mixing in the direction of flow and complete mixing perpendicular to direction of flow. Concentration of reactants varies along the length of reactor but not in radial direction. In case of a coil turbulence is introduced due to frequent change in direction of flow and presence of secondary flow, so a higher value of reaction rate constant is expected in coil tube type plug flow reactor. This set-up is used to study a non-catalytic homogeneous reaction under isothermal condition. The set up consists of two feed tanks through which two reactants are fed to the reactor. Rotameters are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating the needle valves provided on respective Rotameter. The compressed air is used for circulation of feed. It is a helical coil tube type reactor kept in a constant temperature water bath to conduct the experiment at various temperatures. Reactants enter at lower end coming out of the top of coil from where samples are collected for analysis. Pressure Regulator, Pressure Gauge and Safety Valve are fitted in the compressed air line.

 

Learning Objectives/Experiments: 

Ø  Specifications Reaction study in Isothermal Plug Flow Reactor.  

Ø  To determine Reaction Rate Constant and effect of temperature on it. 

 

Required for Operation: 

Ø  Compressed Air Supply at 2 Bar, 0.5 CFM.

Ø  Water supply and drain.

Ø  Electricity-1.5kw, Single.

Ø  Instruments, Laboratory wares and Chemicals required for analysis as per the system adopted.

 

Technical Specifications:

Ø  Reactor: Material Stainless Steel, Capacity 0.7 Ltrs. (approx)  (Helical Coiled Tube Type)

Ø   Water Bath: Material Stainless Steel, Double wall, insulated with CeramicWool.

Ø   Heater: Nichrome wire Heater

Ø   Stirrer (Water Bath): Material SS Impeller and shaft coupled with FHP motor 

Ø   Feed Tank (2Nos.): Capacity - 20 Ltrs.

Ø   Feed Circulation: By compressed air.

Ø   Flow Measurement: Rotameter 2Nos. one each for Reactants

Ø   Piping: Stainless Steel and PVC.

Ø   Pressure Regulator: 0-2 Kg/cm2 

Ø   Pressure Gauge: Bourdon type 0-2 Kg/cm2 

Ø   Stop Watch: Electronic.

Ø   The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure.

 

Control Panel:

Ø  Digital Temp. Controller : 0-200°C, RTD PT-100 type (For Water Bath)

Ø  Standard make on/off switch, Mains Indicator etc.

 

 

    Send Bulk Enquiry
    REQUEST CALLBACK
    Ask Latest Price
    Product Details:
    BrandATICO
    ConditionNew
    Description:
    We carry a large selection of microscopy photography equipment including CCD cameras, USB digital cameras, video capturing cameras, and specialty models for fluorescence microscopy, dark field analysis, and normal brightfield imaging.We have the right camera for every application to record exactly what you see through our high-performance instruments. Photographs with a resolution of more than 12 million pixels, ultra high sensitivity and optimum color fidelity are possible with our Microscope Cameras.

    Specification:

    Bining 1x1, 2x2, 4x4
    Exposure 0.4ms~2000ms
    FPS/ Resolution 1.9@3584x2748
    Pixel 1.67 x 1.67 um

    Features:

    •Easy usage
    •User friendliness
    •Easy installation
    Send Bulk Enquiry
    REQUEST CALLBACK
    Ask Latest Price

    Description:-

    Real reactors do not satisfy the idealized flow patterns, back mix flow or plug flow deviation from ideality can be due to channeling of fluid through the vessel, recycling of fluid within the vessel or due to the presence of stagnant region or pockets of fluid in the vessel. To predict the exact behaviour of a vessel as a Chemicals reactor, RTD or stimulus response technique is used. The setup consists of one feed tank through which water is fed to the reactor. The flow rate can be adjusted by operating the needle valve and measured by Rotameter. The compressed air is used for circulation of feed. The continuously stirred tank reactor made of Stainless Steel is provided for understanding the R.T.D. characteristics. Pressure Regulator & Pressure Gauge are fitted in the compressed air line.

     

    Experimentation:-

    • To plot RTD curve for a CSTR. Using pulse tracer.
    • To determine the Dispersion No.
    Send Bulk Enquiry
    REQUEST CALLBACK
    Ask Latest Price
    Description:
    • The Set-Up Is Used To Study A Photo/Photocatalyc Reaction Using A Uv Source Provided In The Form Of An Uv Tube. This Set-Up Can Be Used To Carry Out A Parameter Study Under Batch/Continuous Flow Condition. A Photo Catalyst Like Tio2 Can Be Used. This Set-Up Can Also Be Used To Study The Mineralization Of Liquid Effluent Industrial Streams & For Purification Of Water.The Set-Up Consists Of Reactor With Inside Reflecting Surface. An Uv Source Surrounding Glass/Quartz Cylinder Is Placed Centrally In The Reactor.
    Utilities Required:
    • Water Supply And Drain
    • Electricity-0.5kw, Single
    • Instruments, Laboratory Wares And Chemicals Required For Analysis As Per The System Adopted
    Technical Details:
    • Uv Source : 30 W / 16 W
    • Reactor: With Inside Reflective Surface. Effective Volume Of Reactor 1 1.5 Ltrs
    • Feed Tank: Material Stainless Steel, Capacity 5 Ltrs
    • Feed Circulation: Magnetic Pump Made Of Polypropylene. Maximum Working Temperature Is 80°C
    • Flow Measurement : Rotameter
    • Sampling Points Are Provided At Inlet & Outlet Of Reactant Line. Control Panel Comprising Of: Standard Make On Off Switch, Mains Indicator, Fuse, Power Supply To Uv Source Etc
    • Instruction Manual : An English Instruction Manual Will Be Provided Along With The Apparatus
    • A Good Quality Painted Rigid Ms Structure Is Provided To Support All The Parts.
    Send Bulk Enquiry
    REQUEST CALLBACK
    Ask Latest Price
    Technical description:
    • Condensation polymerization kettle is used to carry out a condensation polymerization reaction under batch condition. Polymerization reaction can be acid catalyzed or self-catalyzed. The set-up can be used to measure the extent of reaction & also the reaction rate constant. The set-up consists of jacketed type ss reactor fitted with variable speed agitator & baffles. Reactor is fitted with nichrome wire heaters and temperature is controlled by digital temperature controller. Metered quantity of nitrogen gas from a cylinder, allowed entering in the reactor. Set-up is complete & self-contained with sampling ports. The top cover can be removed for cleaning purpose. Feed is fed from top through a funnel provided with s.S. Ball valve. An outlet is given to condenser fitted with a perkin’s triangle for collecting the condensate. Vapours are allowed to enter in the shell of condenser and cooling water is allowed to pass through the tube and condensate is collected.
    Learning objectives/experiments:
    • To study the kinetics of condensation polymerization in a batch reactor under isothermal condition.
    • To calculate the rate constant and extent of reaction with and without acid catalyst.
    Required for operation:
    • Water supply
    • Floor drain.
    • Electricity supply: single phase, 220v ac, 50 hz, 5-15 amp. Combined socket with earth connection.
    • Floor area : 1.5 x 1 m
    • Instruments, laboratory wares and chemicals required for analysis as per the system adopted.
    • High purity n2 gas cylinder with pressure regulator, end connection 1/4" bsp female.
    • A good quality painted rigid ms structure is provided to support all the parts.
    • Technical specifications:
    • Condenser : 18 long 1., concentric tube type
    • Reactor: material stainless steel, volume- 1 ltrs. (approx.)
    • Water bath: material stainless steel, double wall, insulated with ceramic wool.
    • Heater: nichrome wire heater
    • Stirrer (2 nos.): stainless steel impeller and shaft coupled with fhp motor.
    • Stop watch: electronic
    • Temp. Sensor: rtd pt-100 type
    • The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure.
    Control panel:
    • Digital temp. Controller : 0-199.9°c, rtd
    • Pt-100 type(for water bath) cum-indicator
    • With standard make on/off switch, mains indicator fuses etc.
    Send Bulk Enquiry
    REQUEST CALLBACK
    Ask Latest Price

    Technical Description:

    This set-up is used to study a non-catalytic homogeneous second order liquid phase reaction under ambient condition in a combined reactor. It consists of two reactors connected in series, one is plug flow reactor and another mixed flow reactor. In an ideal Plug Flow Reactor (PFTR) there is no mixing in the direction of flow and complete mixing perpendicular to direction of flow. Concentration of reactants varies along the length of reactor but not in radial direction. In case of a coil turbulence is introduced due to frequent change in direction of flow and presence of secondary flow, so a higher value of reaction rate constant is expected in coil tube type plug flow reactor. In an ideal MFR (i.e. an ideal steady state flow reactor) the contents in reactor are well mixed and have uniform composition throughout. Thus the exit stream has the same composition as the fluid within the reactor. The set up consists of two feed tanks through which two reactants are fed to the reactors fitted in series. Rota meters are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating the needle valves provided on respective Rota meter. The compressed air is used for circulation of feed. 1st is a helical coil tube type reactor made up of SS pipe. Reactants enter at lower end coming out of the top of coil from where it is fed to a MFR fitted with stirrer for proper mixing. Samples are collected for analysis. Pressure Regulator, Pressure Gauge and Safety Valve are fitted in the compressed air line.

    The same setup can be used as individual Plug Flow Reactor (Coil Tube type) and Mixed Flow Reactor.

    Learning Objectives/Experiments:

    • Sponification Reaction Study in a Combined Reactor
    • Sponification Reaction Study in Coil Tube Type Plug Flow Reactor
    • Sponification Reaction Study in a MFR.
    • To determine Reaction Rate Constant.

    Required for Operation: 

    • Compressed Air Supply at 2 Bar, 0.5 CFM.
    • Water Supply & Drain
    • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.

    Technical Specifications:

    • 1st Reactor: Material Stainless Steel, Capacity 0.7 Ltrs. (approx)
    • 2nd Reactor: Material Stainless Steel, Capacity 2 Ltrs (Approx).
    • Stirrer for MFR: Stainless Steel Impeller and shaft coupled with FHP motor Remi/Eltek make
    • Feed Tank (2Nos.): Material Stainless Steel, Capacity - 20 Ltrs.
    • Feed circulation: By compressed air.
    • Flow Measurement: Rotameter 2 Nos. (one each for Reactants) Eureka/IEPL make.
    • Piping : Stainless Steel and PVC
    • Pressure Regulator: 0-2 Kg/cm2 Janetics/Shavo Norgen make.
    • Pressure Gauge: Bourdon type 0-2 Kg/cm2 Mass/Pricol make.
    • The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure.
    Send Bulk Enquiry
    REQUEST CALLBACK
    Ask Latest Price

    Technical Description:

    In an ideal Plug Flow Reactor (PFTR) there is no mixing in the direction of flow and complete mixing perpendicular to direction of flow. Concentration of reactants varies along the length of reactor but not in radial direction. This set-up is used to study a non-catalytic homogeneous reaction under ambient condition.  

    The set up consists of two feed tanks through which two reactants are fed to the reactor. Rota meters are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating the needle valves provided on respective Rota meter. The compressed air is used for circulation of feed. A straight tube type reactor kept horizontally and inclined upward at outlet from where samples are collected for analysis. Pressure Regulator, Pressure Gauge and Safety Valve are fitted in the compressed air line. 

     

    Learning Objectives/Experiments: 

    • Sponification Reaction Study in straight tube Plug Flow Reactor. 
    • To determine Reaction Rate Constant. 

     

    Required for Operation: 

    • Compressed Air Supply at 2 Bar, 0.5 CFM. 
    • Water Supply. 
    • Drain. 
    • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.

     

    Technical Specifications:

    • Reactor: Material Borosilicate Glass, OD-32mm, ID-25mm,  Length-1200mm.
    • Feed Tank (2Nos.):  Material Stainless Steel, Capacity - 20Ltrs.
    • Feed Circulation: By compressed air.
    • Flow Measurement: Rotameter 2 Nos. (One each for Reactants).
    • Piping: Stainless Steel and PVC.
    • Pressure Regulator: 0-2 Kg/cm2.
    • Pressure Gauge:   Bourdon type 0-2 Kg/cm2.
    • Stop Watch: Electronic.
    • The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure.

     

    Control Panel:

    • With Standard make on/off switch, Mains Indicator etc.

     

    Scope of Delivery:

    • 1 Self-contained “PLUG FLOW REACTOR (STRAIGHT TUBE REACTOR)” Apparatus.
    • 1 Instruction Manual consisting of experimental procedures, block diagram etc.
    Send Bulk Enquiry
    REQUEST CALLBACK
    Ask Latest Price

    Technical Description: 

     The setup consists of a Reactor in which solid cylinder of Benzoic Acid is placed and water is stirred by means of a variable speed mixer. Baffles are also provided. The Reactor is made of Stainless Steel. A Peltilizer is provided to make the solid cylinder of size 1" diameter and 2" height of Benzoic Acid.

     

    Learning Objectives/Experiments: 

    • To study the Kinetics of dissolution of Benzoic Acid.

     

    Required for Operation: 

    • Water Supply.
    • Drain.
    • Electricity Supply: 1 Phase, 220 V AC, 0.5 kW.
    • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.

     

    Technical Specifications:

    • Chamber : Material Stainless Steel, Capacity 1 Ltrs. (approx)
    • Peltilizer: 1" Diameter, 2" Height (approx).
    • Stirrer : Material Stainless Steel Impeller and shaft coupled with FHP motor
    • The whole unit is assembled rigidly on a base plate and mounted on a stand.
    • Stop Watch 1
    • Spanner OJDE 30 –32 -1
    • The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure.

     

    Control Panel:

    • With Standard make on/off switch, Mains Indicator etc.

     

    Scope of Delivery:

    • 1 Self-contained “KINETICS OF DISSOLUTION OF BENZOIC ACID” Apparatus
    • 1 Instruction Manual consisting of experimental procedures, block diagram etc.
    Send Bulk Enquiry
    REQUEST CALLBACK
    Ask Latest Price
    Product Details:
    BrandATICO
    MaterialStainless Steel
    Description:
    They are Achromatic standard size with outside diameter of 23 mm. They fit most common size compound microscopes. Give your microscope a boost with greater power & clarity at a fraction of cost.

    Specification:
    Material Stainless SteelPixel Size 2.2 um x 2.2 umFrame Model 3.75fps for 5.0 MPMaximum Resolution 2560*1944
    Send Bulk Enquiry
    REQUEST CALLBACK
    Ask Latest Price

    Technical Description:

    In an ideal CSTR (i.e. an ideal steady state flow reactor) the contents in reactor, this set-up are used to study a non-catalytic homogeneous second order liquid phase reaction under ambient condition. The setup consists of three CSTR arranged in series and two feed tanks through which two reactants are fed to the reactor. Rota meters are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating the needle valves provided on respective Rota meter. The compressed air is used for circulation of feed. Reactants from feed tanks enter in the first CSTR and are passed to second CSTR and so on. For analysis samples are collected from different ports provided. Pressure Regulator, Pressure Gauge and Safety Valve are fitted in the compressed air line.  

    Learning Objectives/Experiments: 

    • To study the performance of Cascade of three equal volumes CSTR's in series for the specification of a reaction.
    • To draw the performance chart for the reactor system and evaluate the reaction rate constant at ambient condition.

    Required for Operation: 

    • Compressed Air Supply at 2 Bar, 0.5 CFM.
    • Water Supply.
    • Drain.
    • Electricity Supply: 1 Phase, 220 V AC, 0.5 kW.
    • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.

    Technical Specifications:

    • Reactor (3Nos.): Material Stainless Steel, Capacity 1Ltr. (Approx).
    • Stirrer (3Nos.):   Stainless Steel Impeller and shaft coupled with FHP Motor.
    • Feed Tank (2Nos.):  Material Stainless Steel, Capacity - 20Ltrs.
    • Feed Circulation: By compressed air.
    • Flow Measurement: Rotameter 2 Nos. (one each for Reactants).
    • Piping: Stainless Steel and PVC.
    • Pressure Regulator: 0-2 Kg/cm2.
    • Pressure Gauge:   Bourdon type 0-2 Kg/cm2.
    • Stop Watch: Electronic.
    • The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure.

    Control Panel:

    • Standard make On/Off switch, Mains Indicator etc.

    Scope of Delivery:

    • 1 Self-contained “CASCADE CSTR” Apparatus
    • 1 Instruction Manual consisting of experimental procedures, block diagram etc.
    Send Bulk Enquiry
    REQUEST CALLBACK
    Ask Latest Price

    Technical Description:

    The set-up is used to carry out the emulsion polymerization involving polymerization of a unsaturated monomer like Styrene. Emulsion is of the type: oil in water, monomer is oil soluble & the initiator is water-soluble & an emulsifier is used to create a stable emulsion. Apparatus can be used to generate the kinetic data for emulsion polymerization under various operating conditions like temperature, emulsifier concentration etc. Polymerization is carried out under the atmosphere of air free nitrogen. The set-up consists of jacketed type SS reactor fitted with a variable speed agitator & baffles. Hot water from a digitally controlled water bath is circulated in the jacket using a pump. Metered quantity of nitrogen gas from a cylinder passes through a de-oxygenation column & allowed to enter in the reactor. Air has to be evacuated using a vacuum pump to create vacuum up to 30mm of Hg before passing the nitrogen supply. Initiator from reservoir is supplied to the reactor under pressure. Set-up is complete & self-contained with sampling ports.

     

    Learning Objectives/Experiments:

    • The parameter studies are conducted involving studies of  :
    • Effect of RPM on conversion.
    • Effect of Initiator concentration.
    • Effect of monomer concentration
    • Effect of emulsifier concentration.

     Required for Operation:

    • Water supply and drain.
    • Electricity-1.5kw, Single.
    • Vacuum Pump.
    • High purity N2 gas.
    • Instruments, Laboratory wares and Chemicals required for analysis as per the system adopted.

    Technical Specifications:

    • Reactor : Material Stainless Steel, Total volume of Reactor 1.5 - 2 Ltrs. (approx.)
    • Agitator : Material Stainless Steel Impeller (2 paddles) fitted with Stainless
    • Steel Shaft coupled to DC Motor with Thyristor controlled DC Drive.
    • Flow Measurement : Rota meter for Nitrogen Gas
    • De-Oxygenation Column : Compatible capacity
    • Hot Water Tank: Material Stainless Steel, Double Wall, insulated with ceramic wool.
    • Hot water circulation: Magnetic Pump made of Polypropylene. Maximum working temperature is 80°C.
    • Heaters: Nichrome wire heater.
    • Initiator Reservoir : Capacity 25-50
    • Temperature sensors : RTD PT-100 type 5 Nos
    • The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure.
      Send Bulk Enquiry
      REQUEST CALLBACK
      Ask Latest Price
      Product Details:
      BrandATICO
      Eyepiece (mm)WF10X20MM
      Stereo Angle (Degree)12 Degree
      Zoom1:6.5

      Description: 
      These are the standard accessory that comes along with the USB cameras, Software Driver CD, USB Cable, Microscope Adapters as per your requirement Special Measurement software, Analysis software are also available which can be used for Image analysis. These USB camera can be used for Online viewing of specimen, capture image and do measurement and analysis from any Microscope.

      Specification:

      • Zoom 1:6.5
      • Stereo Angle 12 Degree
      • Eyepiece WF10X20MM
      • Objective 0.5X/2X


      Features:

      •High zooming
      •Sturdiness
      •Easy maintenance


        Send Bulk Enquiry
        REQUEST CALLBACK
        Ask Latest Price
        Product Details:
        BrandATICO
        Technical description:
        • The set-up consists of a glass column. Arrangement is made for changing the glass column conveniently and filling it with any type of packing required. Air from a regulated pressure vessel passes through a sparker and allowed to enter in the column at the top. Liquid is feed from a tank, fitted with a pump and is distributed at the top of a column using a spray nozzle. Set-up is fully accompanied with manometers required. Solenoid valves are provided in the feed line at the top of column for instant release and close. The flow rate can be adjusted by operating the valves provided in respective line.
        Learning objectives/experiments:
        • To determine hydrodynamics of a trickle bed reactor involving the measurement of pressure drop, hold-up & flow regime.
        Required for operation:
        • Compressed air at 4 bar.
        • Water supply and drain. Electricity-0.5kw, single.
        Technical specifications:
        • Packed bed : material borosilicate glass dia. 80mm, height 600mm
        • Packing’s : glass beads dia. 3mm/rasching rings, size 8-10mm
        • Flow measurement: rotameter one each for water and air.
        • Liquid feed tank: material stainless steel capacity 60 ltrs.
        • Feed circulation: centrifugal pump capacity ¼ hp crompton/sharp make.
        • Air tank: compatible capacity.
        • Pressure regulator (2 nos.): 1. Operating range 0-2 kg/cm2 and o-10 kg/cm2
        • Pressure gauge: bourdon type.
        • Mixing chamber: material stainless steel of compatible capacity for air & water.
        • Liquid catch pot: material stainless steel of compatible capacity.
        • Solenoid valve: 2 nos. (one each at liquid and air inlet).
        • Manometers: compatible capacity.
        • Piping: material stainless steel and pvc. ½” line size.
        • Control valves: material gun metal/brass
        • The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure.
        Control panel:
        • Standard make on/off switch, mains indicator etc.
        Scope of delivery:
        • 1 self-contained “hydrodynamics of trickle bed reactor” apparatus.
        • 1 instruction manual consisting of experimental procedures, block diagram etc.
        Send Bulk Enquiry
        REQUEST CALLBACK
        Ask Latest Price
        Technical description:
        • Axial diffusion and dispersion of fluid in packed beds are important for design and operation of separation equipment and chemicals reactors. The tracer technique, the most widely used method for the study of axial dispersion. In stimulus response experimentation, we perturb the system using pulse input of tracer and then see how the system reacts or responds to this stimulus. The analysis of the response gives the desired information about the system. The setup consists of a glass column packed with rasching rings and one feed tank. Water is fed to the reactor through liquid distributor, fitted at the bottom of the column. Rotameter is provided to measure the flow of water. The flow rate can be adjusted by operating the needle valve provided on rotameter. For understanding the r.T.D. Characteristics, a special arrangement to inject tracer into the lower end of reactor, using a syringe, is provided. Samples can be taken periodically from the top outlet of reactor. Pressure regulator & pressure gauge are fitted in the compressed air line.
        Learning objectives/experiments:
        •  To plot rtd curve for packed bed reactor.
        •  To determine the dispersion no.
        Required for operation:
        •  Compressed air supply at 2 bar, 0.25 cfm.
        •  Water supply.
        •  Drain.
        •  Instruments, laboratory glassware and chemicals required for analysis as per the system adopted.
        Technical specifications:
        •  Reactor column: material borosilicate glass
        •  Packing: rasching rings, material borosilicate glass, size 8-10mm (approx)
        •  Feed tank: material stainless steel, capacity - 20 ltrs.
        •  Feed circulation: by compressed air.
        •  Flow measurement: rotameter.
        •  The whole set-up is ingeniously designed and schematically arranged on a powder-coated rigid structure.
        Control panel:
        •  Standard make on/off switch, mains indicator etc.
        Scope of delivery:
        •  1 self-contained “rtd of packed bed reactor” apparatus.
        •  1 instruction manual consisting of experimental procedures, block diagram etc.
        Send Bulk Enquiry
        REQUEST CALLBACK
        Ask Latest Price
        Product Details:
        Automation GradeAutomatic
        BrandATICO

        Description:
        This shop microscope is compact in design and comes with a widefield 10x eyepiece. It is ideal for viewing print, textiles or other industrial applications. Three models are available in 20x, 50x and 100x formats supplied with either 2x, 5x or 10x objectives (160mm tube length). Optional measuring reticles are available and come into sharp focus. Focusing is achieved with the coarse adjustment knob on the side of the barrel.

        Specification:
        Magnification 10 X-300 X
        Objectives M4x,M10x, M20x & M40x.
        Eyepiece WF 10 x
        Voltage 220 V
        Illuminator 6 V / 3 Watt

        Send Bulk Enquiry
        X
         

        Download Brochure
        Explore more products
        Kaplan Turbine Test Rig
        Get Best Quote
        Cascade Control Trainer
        Get Best Quote
        IR Moisture Balance
        Get Best Quote
        Thickness Gauge
        Get Best Quote
        Vacuum Manifold
        Get Best Quote
        Advanced Technocracy Inc.

        Kunal Chopra (CEO)
        ATICO House 5309, Grain Market, Near B.D. Senior Secondary School
        Ambala - 133001
        Haryana, India
        Send Email
        © Advanced Technocracy Inc.. All Rights Reserved (Terms of Use)
        Developed and Managed by IndiaMART InterMESH Limited