Concrete And Cement Testing Equipments

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Tamping Bar.

Made of steel this is 40cm long, having a ramming face of 25mm sq. Other end has a grip, Weight approximate 2kgs.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Cube Moulds.

Specifications These are available in different sized and made according to Indian and British Standard. For the metric size cube moulds, the faces are machined flat to +/-0.02mm accuracy and finished to within 0.2mm. For the inch size moulds, the faces are machined flat to +/-0.01 inches and finished to within 0.01 in. All moulds are supplied complete with base plate

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Cylindrical Moulds.

For Testing concrete cylinders for compressive strength tests.

Specifications: The moulds is split vertically into two parts. The mean internal diameter is within + 0.2mm and height is within + 1mm. The ends are machined to + 0.05. The base plate and top plate are machined flat to + 0.03 mm.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Beam Moulds.

For casting, Concrete specimens for flexure tests.

Specifications: Made of cast iron. The moulds are made of 4 plates assembled together. Each moulds is supplied complete with base plate. Faces are machined flat to +0.2mm. and finished in size to 0.2mm.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Capping Set Horizontal.

For 100mm dia. x 200mm length cylinder.

Specifications: Same as above but for use with specimens 100mm dia. 200mm long.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Capping Set Vertical.

For capping compression cylinder specimens. This apparatus can be used both in the Laboratory and in the field. The specimens capped in this apparatus have plane parallel faces.

Specifications
for cylinders 150mm dia. x 300mm long. Consists of a base with an upright. The upright serves as a guide for positioning the capping plate and the cylinder. The 19mm thick capping plate is machined accurately. There is a recess in the plate for keeping the molten capping compound and to position cylinder. Complete with cylinder carried and ladle.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Capping Set Vertical.

For cylinders 100mm dia. x 20mm long.

Specifications:

Same as above but for cylinders 100mm dia. x 200mm long.

Cylinder Carrier Specifications:

For carrying the concrete cylinders in the Laboratory and in the field. Double handles make it easy to hold the cylinder during capping operations. Complete with snap clamp and cushioning lining. Can be used both for 15cm dia and 10 cm dia cylinders.

Capping Mould:

For capping the concrete cylinders, it consists of an accurately machined plate with a recess for 150mm dia specimen.

Warmer:

An electrically heated and thermostatically controlled bath for melting the capping compound. Supplied with cover and handle. Suitable for operation on 230Volts A.C single phase.

Capping Compound:

Used for capping the ends of concrete cylinders to be tested. Available in packs of 5 kg.

Bowl & Ladle: Metallic bowl is used to carry the capping compound and ladle is used to pour molten capping compound into groves between specimen and capping plate. Supplied as a set.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Vibrating Table.

The vibrating Table is used for compacting concrete cubes and cylinders.

Specifications
It is designed to carry a load of 140Kg. The apparatus consists of a motor fitted with a variable pitch pulley housed in a cabinet. The vibrations are imparted by means of off-balance masses rotating on a shaft of a vibrator clamped to the underside of the table top. The table top is 50cm x 50cm. and has stops along its edges to prevent moulds from walking off the table during vibration. A cross arm adjustable on a vertical rod at the center of the table is provided to hold the moulds while operating the table. The variable pitch pulley arrangement permits the frequency to be varied sleeplessly between a maximum of 3600 vibrations down to 2600 vibrations per minute. A speed regulation handle is provided for increasing or decreasing the frequency. A switch is provided for starting the motor suitable for operation on 1440 volts, 3 phase, 50 cycles, A.C. supply.

Note Vibrating Tables of Tables top size 75cm x 75cm as well as 100cm are also available.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Vibrating Machine (Also Called Mould Vibrator or Mortar Cube Vibrator)

Concrete moulds are easily cast by using a tamping bar or a vibrating table. However air trapped in cement mortal paste can not be thus removed while casting cement mortal moulds. Easy method is to impart greater vibration of lesser amplitude to the mould while casting. This is achieved in a vibrating machine. Vibration of lesser amplitude to the mould while casting. This is achieved in a Vibrating Machine. Vibrating Machine is used for the preparation of mortar cubes for the determination of compression strength of ordinary and rapid hardening Portland cement, Low heat Portland cement, Portland blast furnace cement and high alumina cements.

Specifications

The machine consists of a vibrating frame assembly and an electric motor mounted on a sturdy base. The complete frame assembly consists of a vice to hold a 7.06cm cube mould and two studs threaded at top and a hopper to feed the sample in the mould. This assembly is supported on four springs and has an in built rotating shaft which rotates eccentrically and thus imparts vibrations to the entire frame. A balance weight is an integral bottom part of the frame. The center of gravity of the assembly is brought to the center of the eccentric shaft or within a distance of 25mm below it. The electric motor drives the shaft of the frame and thus imparts required vibrations to the mould. The frequency of vibration is 12000+/-400 vibration per minute. Supplied complete with on 7.06cm cube mould with loose base plate a time switch 0- 5minsx1min and certificate of vibration from a standard Laboratory.

Spares Set of Springs. Belt and Belt guard.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Hydraulic Jack Hand Operated Remote Type.

For applying loads for various tests in the field of Laboratory. Hydraulic jack hand operated with separate pumping units. These jacks are portable and available in various capacities. The pumping unit is connected to the hydraulic jack by means of a flexible connecting pipe 2 meter long. The jack is fitted with lifting handles for easy transportation. The approximate lift of the ram is 90 to 120mm. the pumping unit is a single plunger type with detachable handle. The unit is fixed on a channeled base which is fitted with lifting handles. A pressure release valve is provided on the pumping unit. The load is indicated on 15cm dial hydraulic pressure gauge of appropriate capacity which can be detached from the pump when not in use. The least cont of the calibrated dial will be according to the capacity of the gauge (Normally 100 divisions for full capacity)

¿¿

¿¿

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Integral Type Hydraulic Jacks Capacity (30, 50 & 100 Kn).

These are hydraulic jacks with integral pumping unit. The hydraulic pressure gauge is of 15cm dial on the side of hydraulic jack.
A detachable lever is provided to operate the pump. Lift of the ram is 95 to 100mm. Face of the ram is flat. Note Hydraulic jacks of 1000Kn & 5000KN capacity can be supplied with two speed pumping units. These jacks have lift of approximately 200mm.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Hydraulic Jack Central Hole Type.

Capacity 50 Tonnes.

Specifications

The hydraulic jack has a 25 mm diameter hole going through the center. It is designed for dual direction and had a working stroke of approximately 22cm. A specially designed hand operated pumping unit is supplied for operation in both directions. A detachable handle is provided for operating the pump. The load is indicated on a 15cm dial hydraulic pressure gauge calibrated 0-50000 x 500kg. Note Central hole jacks of other capacities can also be supplied on special request.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Hydraulic Jack Assembly.

Consisting of unto eight jacks connected through a manifold to an electrically operated pumping unit with single/multiple pressure gauges

price on request.

Flexible pipes High Pressure hoses for the hydraulic jacks can be supplied at extra cost. These pipes are available in 1 meter length with end connections. Set of platens for self aligning action.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Pumping Units.

Manufactures a wide ranges of hydraulic pumping units. These are hand operated of electrically operated. The pumping units are suitable for applying load is a load frame of applying pressure to hydraulic jacks. The special features of pumping units is that the plungers of the pump have tolerances and no seals are used in the units and special type of non return valves as against traditional ball valves are used, which gives much longer trouble free service. Electrical Pumping Units work on 230 Volts A.C. or 440 volts A.C.3 phase depending upon their capacity and these can be operated by hand in case of power failure. The front panel accommodate pressure gauge, on/off switch, slow fast lever to control the rate of loading and indicator lamps. Further in electrical units a micro switch fitted in the pressure gauge and a connected to a relay automatically cuts of the power supply to the unit when gauge capacity is reached. A dummy pointer to record maximum load applied is fitted on the cover glass. In hand operated pumping units, two plungers of different diameter are used. The plunger with larger diameter pumps oil at faster rage and is used for initial loading. Further load is easily applied by the second pump which has a smaller diameter plunger, The lever for operation of the pump is sufficiently long to minimize efforts and these units are suitable for site use.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Electrically Operated And Manually Operated Pumping Units.

Note:1. On Electrically operated Pumping Units additional gauge of lower capacity with an isolation valve can be fitted at extra cost. , 2.We can also supply and Electrical Pumping Units of capacity 100 tones or more with a manifold to connect to a number of jacks, maximum upto six jacks. This is useful to structural loading at different points.

Note:

1. On Electrically operated pumping Units additional gauge of lower capacity with an isolation valve can be fitted at extra cost.

2. We can also supply and Electrical Pumping unit of capacity 100 tonnes or more with a manifold to connect to a number of jacks, maximum upto six jacks. This is useful to structural loading at different points.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Compression Testing Machine

Strength of Concrete is a very important aspect during construction. Strength of concrete is obtained by crushing the specimen form of cubes of cylinders. Concrete is carefully designed for a particular compressive strength by the Engineers and specimen is tested by applying load in a compression Testing Machine. Manufactures a range of Compression Testing Machine from 10 Tonnes to 200 Tonnes in different models. Portable models are very convenient and useful for site use where carrying frequently the specimens for testing in a standard Laboratory is inconvenient and uneconomical. With special attachment the machines can also be use for bricks hallow or solid concrete blocks, using appropriate capacity machine In general a Compression Testing Machine consists of a Load Frame with suitable platens and a Pumping Unit with Pressure Gauge, either hand operated or electrically-cum-hand operated. Load Frame and Pumping unit are connected by pressure pipes.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Compression Testing Machine (Pillar Type Load Frame) Hand Operated.

These are four pillar type load frames. Four solid pillars are vertically fixed to a sturdy base and at other end is fixed a cross head. The height of the cross head is also slightly adjustable. A gauge 200mm is fixed in the centre of cross head. To the lower end of this lead screw is fixed upper platen with a spherical seat for self alignment. At the centre of the base plate is fixed a jack, on the top of which the lower platen with the help of a centering pin is kept. The distance between the upper and lower platen is variable by means of the lead screw. A spacer block is also supplied with the load frame. This spacer block which can be fitted on the top of the jack and below the lower platen by means of centering pins helps reduce the distance between the two platens. The platens are well machined, polished and hardened. The lower platen has concentric grooves to centrally place the specimen. A dust cover for jack is supplied to prevent any going in the jack.
Ranges: 50kn to 3000 kn.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Compression Testing Machine Channel Type Load Frame.

In these load frames "C" channels are used, they are welded at the top as well as bottom and with stand high loads. A hydraulic jack is fitted lower platen and spacer block with the help of centering pin. A lead screw passes through the top of the frame. To the lower end of this leads screw is fixed with the upper platen with spherical seat for self alignment. The platens are accurately machined hardened and polished. The lower platen has concentric groves to correctly place the specimen

Note The platens are normally circular in shape, but on special request square platens or rectangular platens can be supplied.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Hand Operated Pumping Unit.

This is a pumping unit double action type with plungers of different diameters. The plunger having larger diameter pumps larger quantities of oil into the jack. Whereas the plunger having smaller diameter pumps oil in smaller quantities but effortlessly these plunger are very accurately machined and fit in their respective cylinders with zero clearance, no seals are used. Special non-return valves are fitted in the pumping unit to ensure correct level of Hydraulic oil. On the front is fitted a release valve, which is to be tightened while applying pressure and loosened to release it, Provision is also made to fix a pressure gauge on the pumping unit, These pumping units are connected to load frame by means of pressure pipes.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Electrically Cum Hand Operated Pumping Unit.

This is a separate console housing an oil tank, electric motor, relay etc. Inside the oil tank are mounted two pumps which are worked with the help of a cam rotating inside the tank. The cam is rotated by the electrical motor and belt. Above the tank is fitted a hand pump. All plungers are accurately machined and no oil seals are used. Special non-return valves are fitted in the pumping system for trouble free long service, A dip stick is provided to know the oil level in the tank. A drain to remove oil is fitted at the base of the tank. The pumping unit has on its front panel a slow-fast lever to control the rate of loading, a release valve and a slit to enable a rod to be inserted in the hand pump to operate the pumping unit manually. A pressure gauge is fitted in front at a convenient angle. The pressure gauge has 200 divisions for its full capacity, Inside the pressure gauge is fitted a micro switch. This micro switch automatically cuts off electrical supply to the pumping unit on reaching full capacity of the pressure gauge. A red dummy pointer is fixed on the cover glass of the pressure gauge to record maximum load at the failure of the specimen. The pumping unit works on 230 volts A.C. or 415 volts, 3 phase supply. This pumping unit is connected to the load frame by means of pressure pipes. Additional pressure gauges (maximum 2 Nos.)
of lower capacities with isolation valves can be fitted on the pumping unit.
Note. Digital versions of electrically operated Compression Testing Machines can also be supplied. The digital versions have 0.5% accuracy. Various Models of Compression Testing Machines are avaiLable listed in the following table.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Aggregate Fine Bulk Density Apparatus.

Stainless steel construction with handles. The top rim is smooth and plane and parallel to the bottom conforming to the standards.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Concrete Pemeability Apparatus.

Concrete Permeability Apparatus

(Single Cell) Same as above but suitable for 150 mm dia X 150mm high sample.

Concrete Permeability Apparatus

(Three Cell Model) Same as above but suitable three cells for samples size 150 mm dia X 150 mm high.

Concrete PermeabilityApparatus

(Single cell) Same as above but suitable for samples size 100 mm dia X 100 mm high.

Concrete Pemeability Apparatus

(Three Cell) Same as above but suitable for three samples of size 100 mm dia X 100 mm high.

Accessories Compressor with pressure gauge 0-20 kg/cm sq. with automatic pressure valve and pressure rubber hose. Suitable for 440 volts A.C. three phase. Specimen casting mould C.I. for 100 mm dia X 100 mm high cylinders. Specimen casting mould C.I. for 150 mm dia X 150 mm high cylinders. Specimen casting mould C.I. for 150 mm cubes. Blow stove 1/2 litre capacity. Resin, Bees wax, Wire brush, Chissel, spare glass cylinder 500 cc capacity.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Concrete Test Hammer Big.

It is similar to the above but is used for testing concrete with over size aggregates (for which test, cubes promise no reliable results) and for testing concrete roads. Its plunger is wider as such, the amount of concrete reached by the impact is considerably greater. With this model also the results obtained are within +/-20% of the actual compressive strength. The instrument is supplied with two handles which can be attached to the body of the concrete test hammer for carrying out the test easily. Complete with grinding stones.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Tensile Strength Tester Electrically Operated.

Specifications

The instrument employs a friction- free, accurate, double lever system, the load being applied by means of sliding weight on the top lever. The capacity of the unit is 900 kgs. After fixing the briquette in the jaws, the machine is switched on. The sliding weight slides over the calibrated lever thus applying tension to the specimen. A micro-switch fitted instantly stops the machine on failure of the briquette and on failure the tensile load is accurately read to 0.5 kg. by means of a marker provided on the sliding weight. The machine can be made op-ratable for subsequent test only after the sliding weight to its zero position. Suitable for operation on 230 volts, 50 cycles, single phase, A.C. supply. Complete with one brass briquette mould and one base plate.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Flexure Testing Machine.
(Electrically Operated) Same as above but instead of a hand pumping unit, a separate electrically cum hand operated pumping unit housed in a cabinet is supplied. The pressure gauge 0-100KN x 1KN, On/off switch and a slow/fast level to control rate of loading are fitted on the front panel of the pumping unit. A facility for hand operation is provided. A micro switch and relay fitted inside the pressure gauge protects the unit from over loading.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Tensile Strength Tester Hand Operate.

Used for making tensile strength test on cement briquettes.

Specifications:
The Instrument is suitable for tensile tests upto 1200 Lbs or 540 kg. It is hand operated, with automatic loading by lead shots. Two calibrated scales 100 Ibs X 1 lb. and 50 kg. X 0.5 kg. are engraved. Supplied complete with one brass briquette mould with base plate, lead shots 15kgs, weights to weigh 50kg., 100kg. 150kg. and 200 kg.

Spares: Lead shots & Briquette mould brass with base plate.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Flexure Testing Machine (Hand Operated).

Flexural tests concrete beam have their own importance in concrete road constructions as well as Building constructions. Normally concrete beams of sizes 10cm x 10cm x 50cm or 15cm x 15cm x 70cm are tested fro flexural strength.

Specifications

The machine consists of a hand operated load frame. The lower platen has two rollers, the distance between the rollers is 600mm, white it is 40mm for beams of size 100mm x 500mm. The upper platen has also a pair or rollers whose distance is adjustable. It is 200mm center to center fro 150mm x 150mm x 700mm size beam and 133mm for 100mm x 100mm x 500mm size beam. A pressure gauge to indicate load is fixed on the load frame. A small pumping unit is attached to the load frame. Total capacity of the machine is 100KN and a 150mm dia. pressure gauge-100KN x 1KN is fitted on the machine. Since this is a hand operated light weight machine, it is useful for field Laboratory also.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Laboratory Jaw Crusher.

The Laboratory jaw Crusher is designed for fast crushing of Aggregates, Ores, Milnerals, Coal, Coke, Chemicals and other similar materials. It is compact and of rugged construction for general Laboratory of small pilot plant operations. Two jaws of manganese steel are provided in this Laboratory jaw Crusher. The moveable jaw produces tow blows for every revolution, thus reducing over sizing to a minimum. A combination of forward and downward strokes with a rocking action exerts pressure on the coarser material, yet permits the finished material to pass through the jaws. A hopper is provided at the top for feeding material The smooth jaws ensure a uniform product and easy cleaning is possible.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Needle Vibrator.

An increasing number of contractual obligations call for various forms of vibro-compacted concrete fro achieving a better and more consistent mixute. The Needle Vibrator is recommended for vibro-compaction test cylinders and beams at site and in the Laboratory. This instrument can also be used at small construction sites. A motor fitted on a swivel base drives a flexible shaft, which in turn, vibrates the needle at about 10,000 vibrations per minute. (approx.)

Specifications

Needle Vibrator with a 25mm. diameter x 350mm, long needle, a one meter long flexible shaft and a motor drive with a swivel head and on/off switch. Wired fro 230V. Sph. 50Hz.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Pulveriser.

The Laboratory Pulverize is a disc type grinder, designed to grind virtually any material to produce a fine mesh sample in one operation. The instrument is useful for assaying , mining and for metallurgical, quarrying, aggregate processing, chemical, geological and industrial Laboratories. It is a self contained grinder, with a rotary disc, having a planetary movement in a vertical plane. This feature gives added life to the moving parts and produces a sample of uniform fineness.

Grinding is done between two discs-one stationery and the other revolving eccentrically at high speed. The discs are made from heat treated machinate metal. With the help of a convenient hand wheel, the size of the final product can be adjusted. This can be done, even while the machine is in operation. A self locking device holds the hinged grinding chamber in place and affords easy and quick access to it, for removal of ground samples and for cleaning. The Pulverize has a capacity of reducing about half of a kilogram of a quartz type sample to 100 mesh in a about a minute. The Pulverser is supplied complete with a 3 H.P motor, a starter, a "V" belt pulley drive and mounting wired for 440V, 3 Ph, 50Hz

LABORATORY PULVERSER

• Disc Diameter - 175mm.
• Maximum Feed size - 6mm.
• Yield - 250gms./min.
• Size of Finished Product -100mesh

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Permeability Apparatus Single Cell Model.

One of the durability tests of concrete is to determine permeability of water through specimen. Permeability apparatus is used for determining the permeability of cement mortar and concrete specimens of 15 cm cubes cast in the Laboratory.

Specifications

The concrete permeability apparatus comprises of a brass/gunmetal cell of squares cross section mounted on a stand and a pressure chamber is connected to the cell through copper tubing and T connector mounted on the stand with sleeve packed vale and rubber hose pipe with end connections. The cell assembly consists of one base
plate, one metal funnel and one top plate, the pressure chamber is fitted with a pressure regulator which helps in regulating the pressure from 0-15kg/cm sq. gauge is for indicating the pressure in the cell. A foot pump and a pressure tube is supplied to develop pressure in the chamber. The apparatus is supplied with a measuring cylinder 500 cc to measure percolated quantity for water. Pressure can also be applied by a pressure air line or by a compressor.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Concrete Test Hammer Small.

The concrete test hammer is an instrument which is easy to use, for quick and approximate measurement of the resistance to pressure of manufactured concrete products. The principles on which it works are based on the rebound impact of a hammer on a piston which rest against the surface of the concrete products. The Greater the resistance on the concrete, greater is the rebounded impact. By reading this rebound impact on a scale and relating it to curves on graphs supplied with the instrument, the resistance to compression in MPA or PSI can be found, with +/-20 % of actual.

Specifications

Consists of a barrel in which is housed a hammer mass attached to an impact spring which slides on a guide bar. A plunger is a attached to the guide bar which is pressed against the surface to be tested. As the piston is pressed against the surface to be tested, on reaching the compressive strength, the hammer mass is released and rebounds to a certain extent (according to the strength of the surface) which is indicated by a rider on a calibrated scale. A lock button fixed on the body of the hammer locks the rider in place and the rider can be richard to zero position by using the same button. The equivalent compressive strength can be computed from the chart supplied. Each hammer is calibrated against at standard test hammer, and is suitable for specimen of compressive strengths 100-700 kg/cm The instrument, complete with a grinding stone for polishing the test surface, is supplied in carrying case

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Tensile Strength Tester.

The instrument has a capacity of 1200 lbs. And is hand operated. Automatic loading by lead shots. Double scale of 100 lbs X 1lb and 50 kg, 150kg and 200kg. Spares and

Accessories: Brass briquette mould for making cement briquette for tensile strength on cement, without base plate. Base plate machined flat to + 0.005 inch. Brass briquette mould three gang complete with base plate.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Thickness Gauge.

A specially designed unit comprises of a plane plate with "L" shaped border and an adjustable stand with a Dial Gauge 0.01 x 25 mm to check the thickness of abased tile specimen of size 7.06 x 7.06 cm.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Tile Abrasion Testing Machine.

This is used for determination of resistance to wear for cement concrete flooring tiles. Tiles specimen of size 7.06cm x 7.06cm is pressed tace-wise under specific load on a grinding path and abrasive powder is evenly spread on the rotating grinding path and after specific number of revolutions of the grinding disc the second parallel side of the tile is subjected to wear for similar number of rotations. The wear of the tile is measured on a thickness gauge specifically made fro the purpose.

The machine consists of a disc rotating at a speed of 30 rpm in a circular tray. A bracket is provided to hold the specimen. A counter balance lever loads the specimen. Load applied is 30kgf. A funnel is fitted to evenly spread abrasive powder on the grinding path. A pre-set counter automatically stops the machine after 22 revolutions. This counter is re-adjustable. The machine works on 440 volts AC, three phase electrical supply. On request machine to operate on 230Volts A.C. supply can also be supplied.

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Tile Flexure Testing Machine.

Unit for finding flexural strength of clay roofing tiles and Cement flooring tiles. Flexural load is applied on the tiles using lead shots. The machine consists of a stand on which two 40mm dia. bearing rollers or 12mm dia. rollers are placed at centre distance of 150mm, 200mm, 250mm, or 2720mm as the case may be, The third upper roller applies centrally flexural load by means of lever arrangement. Lead shot contained in an upper vessel start flowing into lower container at a rate of 45 to 55 kg per minute of 200kg per minute there by, starting loading the specimen. Arrangement is made such that loading automatically stops when specimen breaks. Supplied without lead shots.

Accessory: Lead shot supplied in packs of 20Kgs.